I thought formalin was a five star motel with a tux only lounge.

>>> "Morken, Tim - Labvision"  02/04/05 02:33PM
>>>
I think "Formalin" and "Formal" were trade names from a company and
just
went into common usage.


Tim Morken

-----Original Message-----
From: histonet-bounces@lists.utsouthwestern.edu 
[mailto:histonet-bounces@lists.utsouthwestern.edu] On Behalf Of Bryan
Hewlett
Sent: Friday, February 04, 2005 11:24 AM
To: histonet@lists.utsouthwestern.edu 
Subject: [Histonet] RE: Formaldehyde vs Formalin vs paraformaldehyde
(lengthy)


I was hoping that John Kiernan would jump in reply to this issue with
his
usual eloquence! However, here goes.

Confusion in terminology has been common since Blum introduced this
agent as
a fixative in 1893! It never ceases to amaze me that this should be so,
the
issue has been repeatedly addressed in all major Histotechnology texts
since
before the early fifties ( my student days in the UK).

The following information is from the 10th Edition(1981) of the
Condensed
Chemical Dictionary and the10th Edition(1983) of the Merck Index (the
only
ones at hand).

Formaldehyde is a gas.
It is readily soluble in water up to 55% and is commercially available
to us
as 37%, 44% and 50% aqueous solutions which may contain up to 15%
methanol.
These commercial grades are called Formalin.

Formaldehyde solution (Merck Index)
The USP grade is about 37% (37-40%)  w/v formaldehyde gas in water,
usually
with 10-15% methanol added to prevent polymerization. This solution is
considered to be full strength and is also known as Formalin 100% or
Formalin 40 which signifies that it contains 40 grams of formaldehyde
within
100mL of the solution. It is this solution that produces most of the
confusion since it is referred to and thought of as 100% Formalin.

Paraformaldehyde (Merck Index)
A white crystalline powder of polymerized formaldehyde, obtained by
concentrating formaldehyde solution. Upon solution in water
depolymerization
and evolution of formaldehyde occurs. Thus an aqueous solution
containing 4
grams of paraformaldehyde is essentially the same as a solution of 4%
formaldehyde. There is NO such thing as a solution of
paraformaldehyde.
Right John?

The concentration of formaldehyde used for fixation has been the
subject of
much confusion (see above). The concentration of formaldehyde in
compound
fixatives varies widely - ranging from 0.5 to 15% w/v. The majority of
fixatives, using formaldehyde as the sole fixative agent, have a
concentration of formaldehyde between 2.5 and 4% w/v. The concentration
of
formaldehyde in a fixative should be stated as the percentage by weight
of
the gas, rather than as a percentage of the
formalin(sic) or paraformaldehyde(sic) used to prepare it.

Thus:
"4% formaldehyde" - not 10% formalin.
"4% formaldehyde, from paraformaldehyde" -  not 4% paraformaldehyde.
"NBF
means Neutral buffered formaldehyde" - (not formalin) and is 4% w/v
formaldehyde in phosphate buffer pH 7.0- 7.2.

Bryan Hewlett

Consultant Technologist
QMP-LS






_______________________________________________
Histonet mailing list
Histonet@lists.utsouthwestern.edu 
http://lists.utsouthwestern.edu/mailman/listinfo/histonet 

_______________________________________________
Histonet mailing list
Histonet@lists.utsouthwestern.edu 
http://lists.utsouthwestern.edu/mailman/listinfo/histonet

_______________________________________________
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet